Distinguish between half-wave and full-wave rectifiers.

Half-wave rectifier: (i) The rectified output is for only half of the ac cycle. (ii) One diode is used for rectification. (iii) Secondary of the transformer supplies the input across the two terminals of a diode along with a load. (iv) The output is taken across the load connected in series with the diode. Full-wave rectifier(centre-tapped rectifier): (i) The rectified output is for the complete ac cycle i.e. positive as well as the negative half. (ii) Two diodes are used and each rectifies in the alternate half cycle. (iii) The input by the secondary of a transformer is provided at the two terminals connected to the p - side of the two diodes. (iv) The output is taken between the centre tap of the transformer and the common terminal of the n - sides of two diodes.

What is rectification? Explain the working of a full wave rectifier.

The conversion of alternating current into the direct current is called rectification. Diodes are used for rectification because they allow the unidirectional flow of current. Diodes conduct only when they are forward biased. When two diodes are used in a circuit we get the output voltage during the positive and negative half cycles of the input ac voltage. The circuit for a full-wave rectifier is shown below: For a full-wave rectifier, the secondary of a transformer is provided with a centre-tapping. The p - side of two diodes is connected to the two ends of the secondary of a transformer. The n - side of the diodes are connected together and the output is taken between the common point of diodes and the midpoint of the secondary transformer. We know that a diode conducts when it is forward biased. When A is positive, the diode D 1 conducts and when B is positive then D 2 conducts. Each diode rectifies only for half of the cycle, but the two do it for alternate half cycles. Thus, the output between their common terminal and the centre-tap of the transformer becomes a full-wave rectifier output. The input and output signal of a full-wave rectifier is shown below.

In which bias can a Zener diode be used as voltage regulator?

A zener diode is designed to operate in a breakdown region. As the reverse voltage is increased, after the reverse breakdown voltage, a large change in reverse current is possible by almost an insignificant change in reverse voltage. In other words, the zener voltage remains constant even though the current through zener diode varies over a wide range. Hence, a zener diode is always used in reverse bias for regulating supply voltages.

E M B I B E

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 17

HARD

12th Andhra Pradesh Board

IMPORTANT

Earn 100

Define reverse saturation current in semiconductor diodes.

Important Questions on Semiconductor Electronics: Materials, Devices and Simple Circuits

MEDIUM

12th Andhra Pradesh Board

IMPORTANT

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 18

What is electron mobility? What is its unit?

MEDIUM

12th Andhra Pradesh Board

IMPORTANT

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 19

Are the mobilities of electron and hole equal in a semiconductor?

MEDIUM

12th Andhra Pradesh Board

IMPORTANT

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 20

A diode is called as a unidirectional device. Explain

EASY

12th Andhra Pradesh Board

IMPORTANT

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 21

What do you mean by leakage current in a diode?

EASY

12th Andhra Pradesh Board

IMPORTANT

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 22

Distinguish between avalanche and zener breakdown.

HARD

12th Andhra Pradesh Board

IMPORTANT

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 23

Draw and explain the current-voltage $(I - V)$ characteristic curves of a junction diode in forward and reverse bias.

HARD

12th Andhra Pradesh Board

IMPORTANT

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 24

What is a junction diode? Explain the formation of the depletion region at the junction. Explain the variation of the depletion region in forward and reverse bias condition.

EASY

12th Andhra Pradesh Board

IMPORTANT

Physics Crash Course (Based on Revised Syllabus-2023)>Chapter 15 - Semiconductor Electronics: Materials, Devices and Simple Circuits>Exercise>Q 25

The input voltage applied to a half-wave rectifier is $220 \sin (100 πt) volt$ . The load resistance is $900 Ω$ and forward resistance is $100 Ω$ . Calculate the frequency of the rectified DC.

Learn and Prepare for any exam you want !

|

|

|

|

|

|

|

|